中國工業強基重點產品，中國工信部傳感器一條龍應用計劃示范企業（米朗科技）
中國工信部高精度傳感器一條龍應用計劃示范項目,24小時服務熱線：18988775278
中國工業強基重點產品，中國工信部傳感器一條龍應用計劃示范企業（米朗科技）
中國工信部高精度傳感器一條龍應用計劃示范項目,24小時服務熱線：18988775278
深圳市米朗科技有限公司
電話：18988775278 (陳工)
19926637026（向小姐）
18988775309（單先生）
傳真：0755-81738623
郵箱：rl@miran-tech.com
地址：廣東省深圳市光明區馬田街道合水口社區中糧云景廣場第一棟寫字樓2912室米朗公司
MRG-5232-41 (4L)
油脂稀油一體潤滑油泵微電腦型 Self-controlled Grease and Thin Oil Lubrication Pump
下圖為4 L金屬油箱，材質為鐵或鋁，
另有6 L、8 L、1 0 L等容積可選。
The picture showed as below is metal tank with 4L,
the material is iran ans aluminium, it has 6L,8L and 10L can be choosen.
技術參數Technical Parameters
型號 Model | 電壓頻率 Voltage | 額定轉速 Rated ritary Speed | 功率 Power | 電流 Current(A) | 額定壓力 Rated pressure kgf/cm2 | Z大壓力 Max pressure kgf/cm2 | 容積 Volume | 吐出量 Discharge capacity ml/min | 使用油粘度 Rated pressure kgf/cm2 | 備注 Remarks |
MRG-5232-4100TB | 220V 50/60HZ | 2800 | 60W： 220V 90W： 380V | 60W:0.45 90W:0.32 | 20 | 50 | 4L | 300-500 CC/min | 30#稀油~00#油脂 | MR-5232代表 電壓220V MR-5233代表 電壓380V |
MRG-5232-4100XB | 220V 50/60HZ | |||||||||
MRG-5232-4110XB | 220V 50/60HZ |
*型號帶T為抵抗式，帶X為容積式，不帶" A"為異步電機
*Mode name with " T" is resistant, mode name with “X” is volumetric,without A is asynchronous motor
使用方法Methods
1 .工作時間：請長按鍵,見數字在跳動時，松開S E T鍵SET ，按▲ ▼ 鍵設定個位數;按下SET鍵，按▲ ▼ 鍵設定十位數；
再按下SET鍵，一下SET鍵設定百位數(1-999秒)。
2.間歇時間：請長按SET鍵，見另一個顯示屏數字在跳動時，松開SET鍵，按鍵▲ ▼ 鍵設置個位數；按一下SET鍵，
同時按鍵▲▼約2秒，間歇時間可分秒轉換 (1-999分或1-999秒）。
3.RST 鍵 按住此鍵可重新潤滑或清除異常報警。
4.電路電源接通后系統屬于給油狀態，并進入LUB、 INT循環，
供油時左邊LUB綠燈亮，間歇時右邊INT紅燈亮。
5.ERO 閃爍時代表油量不足，ERP閃爍時代表壓力異常。
6.數顯中框內設有斷電記憶功能，打開小開關﹄進入斷電記憶。
關閉小開關﹄，斷電記憶停止。
7.數顯框內設有按鍵鎖功能﹄，可根據自行需要設置好時間后
是否需鎖住設置按鍵。
（可根據客戶需要定做專屬潤滑方案）
1.Working time: press and hold the SET button, release it when the numbers jump, then press ▲ ▼ to set unit digit; and press the button of SET again, to set ten
digit with pressing ▲ ▼; press SET to hundreds digit(1~999 seconds).
2.Interval time: press and hold the SET button, release it when the numbers in other Display screen jump, then press ▲ ▼ to set unit digit; and press the button of
SET for two seconds, the interval time can shift between minutes and second(1~999 minutes or 1~999 seconds).
3.RST: Press and hold this key to relubricate or clear the abnormal alarm.
4.After the circuit power is turned on, the system belongs to the oil supply state, and enters the LUB, INT cycle. When the fuel is supply , the left LUB green light is
on, the right INT red light is on when the system is on rest.
5.When the ERO flashes, it means that the amount of oil is insufficient, and when the ERP flashes, it means that the pressure is abnormal.
6.There is no power-off memory function in the digital display box, and a small switch is turned on to enter the power-off memory. Turn off the small switch, and the
power off memory stops.
7.There is a key lock function in the digital display box. You can lock the set button after setting the time according to your needs.
(The lubrication program Can be customized)
